home *** CD-ROM | disk | FTP | other *** search
- PANASONIC CM/TF800
-
- NOTES: This is a dual NAM unit.
- The ESN prefix is 136 decimal & 88 hex.
- Panasonic: 201-392-6053
-
-
- NAM PROGRAMING:
-
- 1. Turn power on.
-
- 2. Within 20 seconds enter * 0 # 0 * 0 # 0 * 1 for NAM 1
- or * 0 # 0 * 0 # 0 * 2 for NAM 2.
-
- 3. Each data entry can be looked at by pressing RCL followed by the
- location (step) number below.
-
- 4. To store new data enter the value, press STO followed by the location
- (step) number below. For example to enter a system ID of 00031 enter
- 00031 STO 01. Data can be entered or reviewed in any order.
-
- 5. At any time press STO * * to complete programing.
-
- 6. Press END to exit.
-
-
-
- PROGRAMING DATA:
-
- STEP# #OF DIGITS/RANGE DISPLAY DESCRIPTION
-
- 01 00000 - 32767 SIDH SYSTEM ID
- 02 10 DIGITS OWNDL MIN (AREA CODE & TEL NUMBER)
- 03 0 OR 1 PRESYS PREFERRED SYSTEM
- 04 333 OR 334 IPCH INITIAL PAGING CHANNEL
- 05 2 DIGITS ACCOLC ACCESS OVERLOAD CLASS
- 06 2 DIGITS GIM GROUP ID (10 IN USA)
- 07 2 DIGITS DLMT DIALED DIGIT LIMIT (00= NO LIMIT)
- 08 08 ONLY SCM STATION CLASS MARK
- 09 UP TO 12 DIGITS SPDL SPEED DIAL NUMBER (PERMANENT
- NUMBER STORED IN LOCATION 00)
- 10 2 TO 4 DIGITS LOCK LOCK CODE
- 11 8 DIGIT, 0 OR 1 FCN 1 SEE NOTE 1 BELOW.
- 12 8 DIGIT, 0 OR 1 FCN 2 SEE NOTE 2 BELOW
- 13 8 DIGIT, 0 OR 1 FCN 3 SEE NOTE 3 BELOW
-
-
- NOTES:
-
- 1. Suggested entry is: 11000000.
-
- Bit 7/Digit 1 = Local use Mark
- Bit 6/Digit 2 = MIN Mark
- Bit 5/Digit 3 = Not Used
- Bit 4/Digit 4 = Not Used
- Bit 3/Digit 5 = Not Used
- Bit 2/Digit 6 = Horn Alert
- Bit 1/Digit 7 = Radio Mute
- Bit 0/Digit 8 = Not Used
-
- 2. Suggested entry is: 00010100.
-
- Bit 7/Digit 1 = Not Used
- Bit 6/Digit 2 = Built in Monitor
- Bit 5/Digit 3 = Auto Lock
- (if set to 1 and unlock code is unknown phone will NOT enter program mode.)
- Bit 4/Digit 4 = Full Lock
- Bit 3/Digit 5 = Not Used
- (Enable only one of the following)
- Bit 2/Digit 6 = Allow user A/B select
- Bit 1/Digit 7 = Preferred system only
- Bit 0/Digit 8 = Home system only (no Roam)
-
- 3. Suggested entry is: 11000111.
-
- Digit 1 = Received call indicator
- Digit 2 = Continuous DTMF
- Digit 3 = Not Used
- Digit 4 = Dial Lock
- Digit 5 = Not Used
- Digit 6 = Enable permanent timer (FCN 1)
- Digit 7 = Enable resetable timer (FCN 2)
- Digit 8 = Enable individual call timer
-
-
- READING ESN FROM HANDSET:
-
- 1. Power up phone as above.
-
- 2. Enter * 0 0 0 0 #.
-
- 3. Press * 3 SND.
-
- 4. Press 1 1 SND, phone will display decimal ESN, note that the leading
- "1" of the 136 ESN prefix will be omitted as the phone only has a ten
- digit display capacity.
-
- LOCK: F 3 2 = Dial Lock, F 3 1 = Send lock, F 3 0 = Full lock
-
- UNLOCK: Enter two to four digit code.
-
-
- A/B SYSTEM SELECT:
-
- 1. Phone will default to preferred/non-preferred on every power up.
-
- 2. A only: F 7 2
-
- 3. B only: F 7 3
-
- 4. Home only: F 7 4